Bondcrete RLA 1lt

$28.00
In stock
SKU
9343775004110
  • Buy 5 for $27.30 each and save 2.5%
  • Buy 15 for $26.60 each and save 5%
  • Buy 20 for $26.04 each and save 7%
 
Bondcrete RLA 1lt is available to buy in increments of 1

CreteBond Bonding Agent and Admixture

CreteBond is a versatile polymer emulsion used for a wide range of applications in general construction and around the home.

TYPICAL APPLICATIONS
● Bonding new to old concrete
● Bonding render and hard plaster
● Sealing internal concrete and masonry surfaces
● Admixture for improving the properties of mortar, render and concrete
● Woodworking adhesive

DESCRIPTION

CreteBond is supplied as a high solids emulsion that can be diluted with specified volumes of water to suit particular applications in construction. CreteBond is used as a bonding agent for new to old concrete and as an admixture to improve adhesive and cohesive properties for site mixed mortars, renders and toppings. In addition, CreteBond is an excellent woodworking adhesive when used neat, as supplied. CreteBond is suitable for use on concrete, concrete block, hard plaster, compressed fibre cement sheet, plasterboard and timber.

TYPICAL APPLICATIONS · Bonding new to old concrete · Bonding render and hard plaster · Sealing internal concrete and masonry surfaces · Admixture for improving the properties of mortar, render and concrete · Woodworking adhesive

ADVANTAGES § High solids content (50%) § Interior or exterior use § Water based § Concentrated formula § Versatile range of applications

TYPICAL PROPERTIES Appearance Viscosity (Brookfield Spindle 4/20/25) White liquid 4500 – 5500 cPs Total solids content Specific Gravity 49 – 51% 1.06 ±.01

APPLICATION INSTRUCTIONS Surface Preparation All contacted surfaces must be clean and free any contaminants, wax or resin based curing compounds, oil or grease. All loose or friable material must be removed. Damaged concrete surfaces should be repaired (refer Patch Repair Mortar section below)

Typical Formulations Bonding New to Old Concrete Apply a seal coat (1 part CreteBond to 4 parts water) to existing concrete. Allow to dry. Apply a prime coat (1 part CreteBond to 1 part water) and place concrete topping while the prime coat is sti l tacky. Concrete bond and other properties can be improved by using gauging fluid comprising 1 part CreteBond to 1.5 parts water. Cement Render/Hard Plaster Apply a seal coat (1 part CreteBond to 4 parts water). A low to dry. Apply a prime coat (1 part CreteBond to 1 part water) and apply render/hard plaster while prime coat is sti l tacky. Render can be improved by using gauging fluid comprising 1 part CreteBond to 1.5 parts water. Patch Repair Mortar Add 1 part CreteBond to 1.5 parts water as the gauging fluid. This will increase the strength and bond of patch repair or tiling mortars. Use a seal coat (1 part CreteBond to 4 parts water) to seal the concrete surface prior to application of the patch repair. Sealer Coat CreteBond can be used as a sealer for internal concrete floors to help resistance to penetration by oil and grease. Mix 1 part CreteBond to 4 parts water. Apply to the concrete surface at the rate of 4 – 6 m2 per litre (2 coats recommended) Curing Membrane CreteBond can be used as a low efficiency curing compound to help slow loss of water from the concrete or render surface. Mix 1 part CreteBond to 4 parts water and apply to the concrete or render surface at the rate of 5m2 per litre.

More Information
Brand RLA
Write Your Own Review
You're reviewing:Bondcrete RLA 1lt
Your Rating
Copyright © 2024 Render Supply Co. All rights reserved.